Panasonic BL-WV10A TV Interface for Network Cameras
Easy to Set Up and Watch on TV
Just connect the video cable to a TV to watch the camera images and control up
to 8 cameras. You can set up the network cameras where you want and even access
cameras from across the internet1.
Change the Camera Direction by Remote Control
You can move the camera lens in the direction you want to see by pressing the
cursor key on the remote control or even access your favorite angles by using
the preset controls (numbers 1-8). This simple remote control lets you operate
the camera right from the TV without having to move the camera by hand.
Human Detection Sensor
The built-in
sensor can detect the presence of people and large animals which can trigger
the camera to record images or send an email of the captured image(s) to your
computer or cell phone.
Warning
Buzzer Informs You When Activity is Detected
Each camera can utilize either a built-in
sensor (BL-C10A/BL-C30A) or a commercially available external sensor to detect
activity. When the sensor is triggered a buzzer sound notifies anyone who is
near the TV adaptor.
Easily Record Camera Images
By inserting an SD Memory Card into the unit the camera images can be recorded
onto the card. The recorded images can then be displayed on the TV by remote
control operation.
- The camera must be accessible from the Internet and the TV
adaptor must be connected to a broadband connection.
Interface LAN Ethernet (10Base-T/100Base-TX) x 4 ports
Video output terminal (composite NTSC)
SD Card Slot
Supported Protocols IPv4
TCP UDP HTTP FTP DHCP
Resolution 320 x 240 640 x 480
Image Quality 3 settings (favor clarity standard favor motion)
Image Encoding System JPEG MotionJPEG
Frame Rate Max. 15 frames/sec (320 x 240)
Security User ID and password required for monitoring
Power Source AC Adaptor 12V DC
Supplied Voltage 12V
Camera Connection and Display Up to 8 cameras can be connected and displayed
Displays output in single-screen 8-page mode or 4-screen 2-page mode
Remote Control Operation Yes all connected cameras can be remote-controlled
Camera View Modes Sequential switching
Sensor-activated switching (BL-C10 and Bl-C30 only)
Manual switching
Network Settings On-screen setting
Setting items IP address subnet address gateway DNS server 1 DNS server 2
SD Card Yes
SD Card Functions Still and moving image recording and playback
Setting for sensor-activated and timer recording
Wireless Technology IEEE802.11g and IEEE802.11b
Frequency bandwidth 2412 to 2484 MHz
Channel OFDM Yes (Orthogonal Frequency Division Multiplexing system)
Transmission system
IEEE802.11g 54 Mbps 48 Mbps 36 Mbps 24 Mbps 18 Mbps 12 Mbps 9 Mbps 6
Mbps
IEEE802.11b 11 Mbps 5.5 Mbps 2 Mbps 1 Mbps
Transmission speed Automatic fallback
Repeater Yes
Access Point Yes
Wireless Security WEP (64/128/152 bits)
ESSID ANY access denial (setting required)
ESSID non-transmission within beacon (setting required)
No-response function for probe request (setting required)
The Return Policy below is specified for this product only and is subject to change without notice.
Panasonic BL-WV10A TV Interface for Network Cameras
Item# KX-BL-WV10A
* All returns require an RMA (Return Merchandise Authorization) number, which can be obtained by contacting our Customer Service department.
Defective Returns
Defective unit must be returned back to us within 30 days of the original invoice date. Defective units are replaced for the same product only. Upon receipt of the defective product a new unit will be reshipped at no additional cost.
Non-Defective returns
Product must be returned back to us within 30 days of the original invoice date for a refund. No refunds after 30 days.
* All Return shipping costs is the sole responsibility of the customer under any circumstance.
Please review our Return Guidelines page for more information
Contact Us 1-866-577-8144
